EVA-Kit

The EVA-KIT-SXL for the XT-PICO-SXL, XT-NANO-SXL and XT-FEMTO-SXL offers all functions as well as hardware options in order to completely try out the AK-NORD Embedded-LAN-Modules. One RS232- and one RS485 interfaces as well as an SPI display and an SD card holder are available. Also a POE (PowerOverEthernet) module is included in the EVA-KIT-SXL. One additional WIRE-WRAP field of the contact spacing 2mm allow using or connecting your proper hardware. Using the prepared cables, it is possible to individually separate or connect each bus of the Embedded-Ethernet-Module. One Embedded-LAN-Module and the connection plan are also included in the functional scope.

1x 5Volt Power supply
1x POE IEEE802.3af (Power Over Ethernet)
1x Embedded module SXL
1x SD-CARD slot
1x SPI-DISPLAY
1x RS232
1x RS485

The EVA-KIT-SPE-SXL for the XT-PICO-SPE-SXL, XT-NANO-SPE-SXL and XT-FEMTO-SPE-SXL offers all functions as well as hardware possibilities to fully try out the AK-NORD embedded SPE modules. A RS232 and a RS485 interface as well as a SPI display and a SD card holder are included. An additional WIRE-WRAP - field with a pitch of 2mm allows to use or connect own hardware. With prepared plug-in cables each bus of the embedded SPE modules can be disconnected or connected separately. An embedded SPE module, e.g. XT-PICO-SPE-SXL, XT-NANO-SPE-SXL or XT-FEMTO-SPE-SXL, as well as the circuit diagram are also included in the functional scope.

1x 5Volt Power supply
1x XT-PICO-SPE-SXL or 1x XT-NANO-SPE-SXL or 1x XT-FEMTO-SPE-SXL
1x SD-CARD slot
1x SPI-DISPLAY
1x RS232
1x RS485

The mini EVA-KIT-LXL for the XT-ATTO-LXL offers all functions and hardware options to fully test the AK-NORD Embedded-LXL module. It includes an RJ45 socket and a USB host interface as well as a USB debug interface and an SD card holder. All other pins of the ATTO module are routed out via a double pin header, which makes it possible to use or connect your own hardware. With numerous optional shields, each interface can be fully tested. The schematics for the shields are freely available. So you can also design your own shields and put them into operation.

1x 5Volt Power supply
1x RJ45
1x SD-CARD
1x USB-A
1x Debug USB

The Shield-DISPLAY can be plugged onto the top of the mini EVA-KIT-LXL. This allows the 0.96 inch OLED display to be controlled via the I2C interface. The resolution is 128 x 64 pixels.

The Shield-CAN can be plugged onto the top of the mini EVA-KIT-LXL. This allows you to start developing your software directly before your own hardware has been fully developed.
This can be used to fully test the CAN interface of the ATTO-LXL module.

The Shield-RS232 can be plugged onto the top of the mini EVA-KIT-LXL. This allows you to start developing your software directly before your own hardware has been fully developed.
This can be used to access and fully test the RS232 interface from the ATTO-LXL module.

1x RS232

The Shield-RS485 can be plugged onto the top of the mini EVA-KIT-LXL. This allows you to start developing and testing your software even before your own hardware has been fully developed.
This can be used to fully test the RS485 interface on the ATTO-LXL module. The termination resistors are implemented via jumpers and can be activated if required.

1x RS485

The Shield-HSIC-LAN can be plugged onto the top of the mini EVA-KIT-LXL. This allows you to start developing and testing your software even before your own hardware has been fully developed.
This can be used to fully test a second Ethernet interface on the ATTO-LXL module. The second network card is connected via USB-HSIC connection. This makes it possible to realize projects such as routers that are connected to two separate networks.

1x RJ45